Contents Introduction Warning Caution Main Unit Description Remote Control OSD basic adjustment DVD manual Specifications Trouble Shooting 1 Introduction Thank you very much for your purchase of our product of LCD TV. It serves as a normal color TV and PC monitor. To enjoy your set to the full from the very beginning, read this manual carefully and keep it handy for ready reference. INSTALLATION Locate the receiver in the room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Allow enough space between the receiver and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure. This TV receiver can be connected to AC100-240V 50/60HZ. Do not install the receiver in a location near heat sources such as radiator, air ducts, direct sunlight, or in a place somewhere like close compartment and close area. Do not cover the ventilation openings when using the set. The indicator light will last about 30 seconds to go out after cutting off the electricity, during this period, you cannot repower it on until the indicator light goes out. Thanks a lot for your attention! 2 Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to avoid the risk of electric shock, do not disassemble this equipment by anyone except a qualified service personnel. This symbol is intended to alert the user to the presence of important operation and maintenance instructions in the literature accompanying the equipment. 3 Caution Caution High voltages are used in the operation of this product. Do not remove the back cabinet from your set. Refer servicing to qualified service personnel. Caution To prevent fire or electrical shock hazard, Do not expose the main unit to moisture. Caution Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver. Caution Avoid exposing the main unit to direct sunlight and other source of the heat. Do not stand the television receiver directly on other produces which give off heat. E. g. video cassette players, Audio amplifiers. Do not block the ventilation holes in the back cover. Ventilation is essential to prevent failure of electrical component. Do not squash power supply cord under the main unit. 4 Caution Caution Never stand on, lean on, push suddenly the product or its stand. You should pay special attention to children. Caution Do not place the main unit on an unstable cart stand, shelf or table. Serious injury to an individual, and damage to the television, may result if it should fall. Caution When the product is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet. Caution The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks. 5 Main unit description Control Panel Button Function VOL+ : Volume up. VOL- : Volume down. CH+ : TV channel up. CH- : TV channel down. MENU : Press to select the main menu. TV/AV : Select the input signal. POWER : Switch on when at standby mode or enter the standby mode. TV Terminal Connections 1. HDMI input terminal. 2. VGA input terminal of simulation signal of PC. 3. SCART input terminal. 4. S-video input terminal. 5. Video input terminal. 6. AUDIO input terminal. 7. PC AUDIO terminal. 8. HEADPHONE output terminal. 9. ATV antenna/close circuit TV network port. Power Input Configuration AC POWER 6 Remote control POWER: Power on/off button, press once to turn the TV on and press again to turn the TV off. MUTE: Press this button to mute or restore sound. DVD SETUP: Press this button to enter the DVD main menu and press again to exit the main menu. (Used for models with DVD function only) TITLE: Press this button to return the title menu. (Used for models with DVD function only) MENU(BLUE): Press this button to return the root menu or exit the DVD main menu. (Used for models with DVD function only) USB/CR: Press to select the MEDIA signal source. (Used for models with USB/CR function only) NICAM/A2: In the TV condition, press this key to select the stereo effects. SLEEP: Set the sleep timer. ASPECT: Press to select the different picture size. EJECT : press to eject the DVD-disc in DVD mode. (Used for models with DVD function only) DISPLAY: Display TV information. AUTO: Press to adjust the picture automatically in PC mode. PMODE: Select picture mode. SMODE: Select sound mode. DTV: This button is not available. SOURCE: Press to change signal source. ENTER: Enter the selected option or perform the selected operation. MENU: Press this button to enter the main menu for various optional adjustable setting. EXIT: Exit the OSD (On-screen display). 0-9: Select and switch to a channel using 0 - 9. -/--: Switch the program digit. : Switch back and front between the current and previous channels. 7 CH /CH : Change the channel up and down. VOL /VOL : Adjust the volume. TEXT: Press to enter the Teletext mode. HOLD: Freeze a multi-page passage on screen in Teletext mode. INDEX: Press this button to go to the index page. REVEAL: Press this button to reveal the hidden information in Teletext page. Press again to hide the information. SIZE: Display the top, bottom or all of page to read easily in Teletext mode. SUBPAGE: Carry out the function of SUBCODE in the text while enter the text display mode. PLAY/PAUSE Press to start playing the disc or Media, or to pause playing. (Used for models with DVD or USB/CR function only) STOP Stop playing the disc or Media. (Used for models with DVD or USB/CR function only) Press to play backward. REV (Used for models with DVD or USB/CR function only) Press to play forward. FWD (Used for models with DVD or USB/CR function only) : Skip to previous chapter PREV (Used for models with DVD or USB/CR function only) Skip to next chapter NEXT (Used for models with DVD or USB/CR function only) ZOOM Select the zoom picture. (Used for models with DVD function only) GOTO Jump to the appointed chapter or title. (Used for models with DVD function only) SUBTITLE(BLUE) Select the disc caption. (Used for models with DVD function only) ANGLE Select the angle. (Used for models with DVD function only) 8 PROGRAM Select the disc program. (Used for models with DVD function) INTRO Press the button to display the time of chapter remain or elapsed. (Used for models with DVD function) REPEAT Select the repeat mode. (Used for models with DVD function) AB Select the segment to repeat. (Used for models with DVD function) RED, GREEN, YELLOW, BLUE: Correspond to the different colored subjects. (Used for models with european region function) 9 OSD basic adjustment PICTURE You can select the type of picture, which best corresponds to your viewing. 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "PICTURE" menu. Enter the "PICTURE" menu by pressing " " button. 2. Press " / " button to select "PICTURE MODE" and press the " / " button to select the picture mode . 3. Press " / " button to select "BRIGHTNESS" and press the " / " button to enter brightness adjustment menu to adjust brightness. 4. Press " / " button to select "CONTRAST" and press the " / " button to enter contrast adjustment menu to adjust contrast. 5. Press " / " button to select "SATURATION" and press the " / " button to enter color adjustment menu to adjust saturation. 6. Press " / " button to select "SHARPNESS" and press the " / " button to enter sharpness adjustment menu to adjust sharpness. 7. Press " / " button to select "HUE" and press the " / " button to enter hue adjustment menu to adjust hue. Note: The item hue is only for NTSC 8. Press " / " button to select "COLOUR TEMP" menu and press the " / " button to select the color temp. SOUND You can select the type of sound, which best corresponds to your listening. 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "SOUND" menu. Enter the "SOUND" menu by pressing " " button . 2. Press " / " button to select "SOUND MODE" and press the " / " button to select the sound mode. 3. Press " / " button to select "BASS" and press the " / " button to enter bass adjustment menu to adjust bass. 10 4. 5. 6. 7. Press " / " button to select "TREBLE" and press the " / " button to enter treble adjustment menu to adjust treble. Press " / " button to select "BALANCE" and press the " / " button to enter balance adjustment menu to adjust balance. Press " / " button to select "AVL" and press the " / "button to select the avl function on or off. Press " / " button to select "EQ" and press the "ENTER" button to enter. Press " / " button to select the frequency of wave band and press the " / " button to adjust . FUNCTION 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "FUNCTION" menu. Enter the "FUNCTION" menu by pressing " " button . 2. Press " / " button to select "LANGUAGE" menu and press the " / " button to select the OSD language which you desire. 3. Press " / " button to select "OSD DURATION" and press the " / " button to select the OSD duration which you desire. 4. Press " / " button to select "ASPECT RATIO" and press the " / " button to select the aspect ratio which you desire. 5. Press " / " button to select "TT LANGUAGE" menu and press the " / " button to select local teletext language. 6. Press " / " button to select "RESET" and press the "ENTER" button to enter. Press the " / " button to select "YES" or "NO" and press "ENTER" button to confirm. Select "YES" to reset the function and select "NO" to return the previous menu. 11 TV You can make the desired adjustment in the TV mode. 1. Press " / " button to select "CHANNEL" and press the " / " button to select the different channel. 2. Press " / " button to select "AUTO SEARCH" and press the "ENTER" button to enter. Press the " / " button to select "YES" or "NO" and press "ENTER" button to confirm . Select "YES" to do auto search and select "NO" to return the previous menu. 3.Press" / " button to select "MANU.SEARCH" and press the " / " button to enter. Press the " / " button to select "YES" or "NO" and press "ENTER" button to confirm . Select "YES" to do manual search and select "NO" to return the previous menu. 4. Press " / " button to select "FINE TUNE" and press the " / " button to select the frequency which you want to fine tune. 5. Press " / " button to select "COLOR SYSTEM" and press the " / " button to select the local color system . 6. Press " / " button to select "SOUND SYSTEM" and press the " / " button to select the local sound system. 7. Press " / " button to select "CHANNEL EDIT" and press the "ENTER" button to enter. a. Press " / " button to select one channel and press "RED" button to pitch on. Press " / " button to select another channel which you want to swap . Press "ENTER" button to confirm. b. Press " / " button to select one channel and press "GREEN" button to pitch on. Press " / " button to select another channel which you want to insert . Press "ENTER" button to confirm. c. Press " / " button to select one channel and press "YELLOW" button to pitch on.. Press " / " button to select another channel which you want to copy. Press "ENTER" button to confirm. 12 d. Press " / " button to select the channel which you want to delete and press "BLUE" button to pitch on. Press "ENTER" button to confirm. e. Press " / " button to select the channel in the list, press "ENTER" button to enter the "EDIT SUB" menu. f. Press " / " button to select CHANNEL " EDIT NAME"menu and press "ENTER" button to enter the rename channel's window. Input channel name at "____", press "/ / " button to select "letter", "number", "_", "", "", "EMPTY" or "BAK SPC", and press "ENTER" button to confirm. Press " / / " button to select "OK" to save and return to the previous menu. Press " / / " button to select "CANCEL" to exit and return to the previous menu. 8. Press " / " button to select "SKIP" and press the " / "button to select skip the channel on or off. PC 1. Press the "MENU" button to enter the OSD menu. Then press " / " button to select the "PC" menu. Enter the "PC" menu by pressing " " button. 2. Press " / " button to select "H POSITION" menu and press the " / " button to enter "H Position" adjustment menu to adjust "H Position". 3. Press " / " button to select "V POSITION" and press the " / " button to enter "V Position" adjustment menu to adjust "V Position". 4. Press " / " button to select "PHASE" and press the " / " button to enter ...